The Faint Intergalactic Medium Redshifted Emission Balloon (FIREBall-2) is a UV multi-object spectrograph designed to detect emission from the circumgalactic and circumquasar medium at low redshifts (0.3 < z < 1.0). The FIREBall-2 spectrograph uses a suborbital balloon vehicle to access a stratospheric transmission window centered around 205 nm and is fed by a 1-m primary parabolic mirror and a 2-mirror field corrector that allows an ≈11’ x 35’ field of view. The slit-mask spectrograph can access dozens of galaxy targets per field, with each target spectrum read out on a UV electron-multiplying CCD detector. Following a flight in 2018, several refurbishments and modifications were made to the instrument and telescope to prepare for additional flight opportunities. Here we present an overview of upgrades and improvements made since the previous flight and discuss the 2023 field campaign, which culminated in a flight from Fort Sumner, New Mexico in September, 2023.
Aspera is a NASA Pioneers SmallSat mission designed to detect and map the O VI emission (1032 Å) through long-slit spectroscopy in the halos of nearby galaxies for the first time. The spectrograph utilizes toroidal gratings with multilayer coatings of aluminum, lithium fluoride, and magnesium fluoride that optimize their throughput in the extreme ultraviolet EUV waveband of 1030 to 1040 Å. We discuss the grating verification test setup design, including optical alignment and reference measurement setup. We also present grating testing and grating efficiency simulation results using the target grating groove profile and the multi-layer coatings.
The Faint Intergalactic-medium Redshifted Emission Balloon (FB-2), a collaborative NASA/CNES suborbital balloon telescope, targets the mapping of faint UV emissions from the circumgalactic medium around low-redshift galaxies. The initial September 2018 flight encountered challenges, including a balloon breach and subsequent damage during landing, impacting the two large telescope mirrors and the critical focal corrector. Likely due to landing shock, the focal corrector experienced misalignment beyond tolerance, necessitating reevaluation and realignment. This paper outlines a comprehensive approach to realigning the focal corrector using a computer-generated hologram (CGH) and a Zygo interferometer for feedback. The CGH enables precise alignment corrections in various degrees of freedom, while interferometer feedback aids in reducing aberrations. The paper details the methodology for optical alignment, surface measurement, and performance evaluation of the focal corrector, emphasizing its successful integration into the FB-2 spectrograph in early 2023 for the September 2023 flight.
Aspera is a NASA Pioneers Mission designed to measure faint OVI emission around nearby galaxies with unprecedented sensitivity. The SmallSat payload consists of two identical co-aligned spectrographs, both operating in the Far Ultraviolet (FUV) between 1030−1040 Å. Missions operating at FUV wavelengths are particularly sensitive to contamination, as short wavelengths are easily scattered and absorbed by contaminants deposited on payload optical surfaces. A strict contamination control plan is critical to avoiding a severe loss in FUV throughput. Aspera contamination control efforts have been tailored to fit within the scope of a sub-Class D mission, a challenge that has become increasingly relevant as advances in FUV optics/detectors drive an uptick in smaller platform, contamination sensitive UV payloads. Contamination monitoring is used to audit the cleanroom environment, avoid outgassing contaminants under vacuum, and assess contaminant levels on payload optics. We present a detailed contamination budget through the mission end of life as well as our ongoing contamination monitoring efforts. We discuss protocols implemented for minimizing contamination-related performance degradation.
Aspera is a NASA-funded UV SmallSat mission designed to detect and map warm-hot phase halo gas around nearby galaxies. The Aspera payload is designed to detect faint diffuse O VI emission at around 103.2 nm, satisfying the sensitivity requirement of 5×10−19 erg/s/cm2/arcsec2 over 179 hours of exposure. In this manuscript, we describe the overall payload design of Aspera. The payload comprises two identical co-aligned UV long-slit spectrograph optical channels sharing a common UV-sensitive microchannel plate detector. The design delivers spectral resolution R ∼ 2,000 over the wavelength range of 101 to 106 nm. The field of view of each channel is 1 degree by 30 arcsec, with an effective area of 1.1 cm2. The mission is now entering the payload integration and testing phase, with the projected launch-ready date set for late 2025 or early 2026. The mission will be launched into low-Earth orbit via rideshare.
Aspera is a NASA Astrophysics Pioneers SmallSat mission designed to study diffuse Ovi emission from the warm-hot phase gas in the halos of nearby galaxies. Its payload consists of two identical Rowland Circle-type long-slit spectrographs, sharing a single MicroChannel plate detector. Each spectrograph channel consists of an off-axis parabola primary mirror and a toroidal diffraction grating optimized for the 1013-1057 Å bandpass. Despite the simple configuration, the optical alignment/integration process for Aspera is challenging due to tight optical alignment tolerances, driven by the compact form factor, and the contamination sensitivity of the Far-Ultraviolet optics and detectors. In this paper, we discuss implementing a novel multi-phase approach to meet these requirements using state-of-the-art optical metrology tools. For coarsely positioning the optics we use a blue-laser 3D scanner while the fine alignment is done with a Zygo interferometer and a custom computer-generated hologram. The detector focus requires iterative in-vacuum alignment using a Vacuum UV collimator. The alignment is done in a controlled cleanroom facility at the University of Arizona.
We present the integration of a new calibration system into the Faint Intergalactic-medium Redshifted Emission Balloon-2 (FIREBall-2), which added in-flight calibration capability for the recent September 2023 flight. This system is composed of a calibration source box containing zinc and deuterium lamp sources, focusing optics, electronics, sensors, and a fiber-fed calibration cap with an optical shutter mounted on the spectrograph tank. We discuss how the calibration cap is optimized to be evenly illuminated through non-sequential modeling for the near-UV (191 to 221 nm) for spectrograph slit mask position calibration, electron multiplying charged-coupled device (EMCCD) gain amplification verification, and wavelength calibration. Then, we present the pre-flight performance testing results of the calibration system and their implications for in-flight measurements. FIREBall-2 flew in 2023, but did not collect calibration data due to early termination of the flight.
Aspera is a NASA-funded UV SmallSat Mission in development with a projected launch in 2025. The goal of the mission is to detect and map warm-hot gas in the circumgalactic medium of nearby galaxies traced by the Ovi emission line at 103.2 nm. To that goal, Aspera will conduct long-exposure observations at one or more spatial fields around each target galaxy, employing two long-slit spectrographs. Spectra from both channels are focused on a single micro-channel plate detector. In preparation of the mission’s launch, we are developing a data reduction pipeline, the goal of which is to reconstruct a calibrated 3D IFU-like data cube by combining the photon event lists obtained during each observation for a given target galaxy. In this proceedings paper, we present an outline for the data reduction pipeline and describe the data flow through the processing of science observations. We will further discuss individual steps to be applied to the data during the processing and show how our final data cubes shall be reconstructed. Finally, we will present our planned data products and discuss how simulations of the Aspera data cubes are being used to develop the pipeline.
The integration of a new calibration system into FIREBall-2 (Faint Intergalactic Redshifted Emission Balloon-2) allows in-flight calibration capability for the upcoming Fall 2023 flight. This system is made up of a calibration box that contains zinc and deuterium lamp sources, focusing optics, electronics, and sensors, and a fiber-fed calibration cap with an optical shutter mounted on the spectrograph tank. We discuss how the calibration cap is optimized to be evenly illuminated through nonsequential modeling for the near-UV (200-208nm). Then, we present the pre-flight performance testing results of the calibration system and their implications for in-flight measurements.
Aspera is the UV small-satellite mission to detect and map the warm-hot phase gas in nearby galaxy halo. Aspera was chosen as one of NASA's Astrophysics Pioneers missions in 2021 and employs a FUV long-slit spectrograph payload, optimized for low-surface brightness O VI emission line detection at 103-104 nm. The mission incorporates state-of-the-art UV technologies such as high-efficiency micro-channel plates and enhanced LiF coating to achieve a high level of diffuse-source sensitivity of the payload, down to 5.0E-19 erg/s/cm^2/arcsec^2. The combination of the high sensitivity and a 1-degree by 30-arcsecond long-slit field of view enables efficient 2D mapping of diffuse halo gas through step and stare concept observation. Aspera is presently in the critical design phase, with an expected launch date in mid-2025. This work provides a current overview of the Aspera payload design.
We present a comprehensive stray light analysis and mitigation strategy for the FIREBall-2 ultraviolet balloon telescope. Using nonsequential optical modeling, we identified the most problematic stray light paths, which impacted telescope performance during the 2018 flight campaign. After confirming the correspondence between the simulation results and postflight calibration measurements of stray light contributions, a system of baffles was designed to minimize stray light contamination. The baffles were fabricated and coated to maximize stray light collection ability. Once completed, the baffles will be integrated into FIREBall-2 and tested for performance preceding the upcoming flight campaign. Given our analysis results, we anticipate a substantial reduction in the effects of stray light.
A comprehensive education of optical engineers is of paramount importance to the development of the industry. While optical sciences and engineering curricula are set up to teach theoretical concepts comprehensively, there appears to be a lack of required coursework that teaches students how to use industry-standard software that they will inevitably use in their careers. The Practical Optics Workshop (POW) is an initiative at the University of Arizona’s Wyant College of Optical Sciences to support the education of students that use optical design software. POW’s aim is to bridge the gap between the theory of optical system design and the problems the optical engineers of the future will face daily. POW has principally engaged students through short workshop sessions and optical design problems through inquiry-based learning activities. However, during the COVID-19 pandemic new activities have been designed to support self-paced and virtual learning to ensure the accessibility of Optical Design software education. We present the status of POW’s current initiatives and how they have impacted student learning, as well as the design of future initiatives that POW is developing for a self-paced curriculum.
This conference presentation was prepared for the Space Telescopes and Instrumentation 2022: Ultraviolet to Gamma Ray conference at SPIE Astronomical Telescopes and Instrumentation, 2022.
We present a comprehensive stray light analysis and mitigation strategy for the FIREBall-2 UV telescope. Using non-sequential optical modeling, we identified the most problematic stray light paths which impacted telescope performance during the 2018 flight campaign. After confirming the correspondence between the simulation results and post-flight calibration measurements of stray light contributions, a system of baffles was designed to minimize stray light contamination. The baffles were fabricated and coated to maximize stray light collection ability. Once completed, the baffles will be integrated into FIREBall-2 and tested for performance preceding the upcoming flight campaign. Given our analysis results, we anticipate a substantial reduction in the effects of stray light.
Aspera is an extreme-UV (EUV) Astrophysics small satellite telescope designed to map the warm-hot phase coronal gas around nearby galaxy halos. Theory suggests that this gas is a significant fraction of a galaxy’s halo mass and plays a critical role in its evolution, but its exact role is poorly understood. Aspera observes this warm-hot phase gas via Ovi emission at 1032 °A using four parallel Rowland-Circle-like spectrograph channels in a single payload. Aspera’s robust-and-simple design is inspired by the FUSE spectrograph, but with smaller, four 6.2 cm × 3.7 cm, off-axis parabolic primary mirrors. Aspera is expected to achieve a sensitivity of 4.3×10−19 erg/s/cm2/arcsec2 for diffuse Ovi line emission. This superb sensitivity is enabled by technological advancements over the last decade in UV coatings, gratings, and detectors. Here we present the overall payload design of the Aspera telescope and its expected performance. Aspera is funded by the inaugural 2020 NASA Astrophysics Pioneers program, with a projected launch in late 2024.
The Faint Intergalactic-medium Redshifted Emission Balloon (FIREBall-2, FB-2) is designed to discover and map faint UV emission from the circumgalactic medium around low redshift galaxies (z ~ 0.3 (C IV); z ~ 0.7 (Lyα); z ~ 1.0 (O VI)). FIREBall-2's first launch, on September 22nd 2018 out of Ft. Sumner, NM, was abruptly cut short due to a hole that developed in the balloon. FIREBall-2 was unable to observe above its minimum require altitude (25 km; nominal: 32 km) for its shortest required time (2 hours; nominal: 8+ hours). The shape of the deflated balloon, as well as a concurrent full moon close to our observed target field, revealed a severe, off-axis scattered light path directly to the UV science detector. Additional damage to FB-2 added complications to the ongoing effort to prepare FB-2 for a quick re-flight. Upon landing, several mirrors in the optical chain, including the two large telescope mirrors, were damaged, resulting in chunks of material broken off the sides and reflecting surfaces. The magnifying optical element, called the focal corrector, was discovered to be misaligned beyond tolerance after the 2018 flight, with one of its two mirrors damaged from the landing impact. We describe the steps taken thus far to mitigate the damage to the optics, as well as procedures and results from the ongoing efforts to re-align the focal corrector and spectrograph optics. We report the throughput of the spectrograph before and after the 2018 flight and plans for improving it. Finally, we describe several methods by which we address the scattered light issues seen from FIREBall-2's 2018 campaign and present the current status of FB-2 to fly during the summer campaign in Palestine, TX in 2020.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.