Astrophotonic technologies, specifically mass-produced “spectrometers-on-a-chip,” offer an exciting path toward dramatically reducing the cost-per-spectrum of astronomical spectrographs. This technology could one day enable significant multiplexing upgrades to fiber-based instruments and inspire new facilities capable of collecting 100,000 simultaneous spectra in both single-fiber and IFU formats. Here, we report on a new astrophotonics platform at Lick Observatory for on-sky testing of such technologies. Our initial focus is on the problem of efficiently coupling telescope light into photonic devices, which are typically optimized to work with a single mode, i.e., with diffraction-limited light. While photonic lanterns can deliver multiple single-mode outputs given multi-modal input, here we introduce the concept of Adaptive Mode Extraction (AME), which uses a second, reference lantern to select the brightest instantaneous mode or modes for injection into photonic devices. Analogous to “speckle spectroscopy,” this technique has the potential to increase the signal-to-noise ratio for faint sources by spatially filtering out the sky background. We have deployed our testing platform behind the AO system at the Shane Telescope and demonstrate that it meets requirements for our planned on-sky tests of AME, namely the ability to couple AO-corrected light from two nearby stars (within 2′′) into two dynamically-positioned lanterns, with adequate throughput (<40%) and image quality (0.15′′).
The Lick Observatory's Shane 3-meter telescope has been upgraded with a new infrared instrument (ShARCS - Shane Adaptive optics infraRed Camera and Spectrograph) and dual-deformable mirror adaptive optics (AO) system (ShaneAO). We present first-light measurements of imaging sensitivity in the Ks band. We compare mea- sured results to predicted signal-to-noise ratio and magnitude limits from modeling the emissivity and throughput of ShaneAO and ShARCS. The model was validated by comparing its results to the Keck telescope adaptive optics system model and then by estimating the sky background and limiting magnitudes for IRCAL, the pre- vious infra-red detector on the Shane telescope, and comparing to measured, published results. We predict that the ShaneAO system will measure lower sky backgrounds and achieve 20% higher throughput across the JHK bands despite having more optical surfaces than the current system. It will enable imaging of fainter objects (by 1-2 magnitudes) and will be faster to reach a fiducial signal-to-noise ratio by a factor of 10-13. We highlight the improvements in performance over the previous AO system and its camera, IRCAL.
A Cassegrain mounted adaptive optics instrument presents unique challenges for opto-mechanical design. The flexure and temperature tolerances for stability are tighter than those of seeing limited instruments. This criteria requires particular attention to material properties and mounting techniques. This paper addresses the mechanical designs developed to meet the optical functional requirements. One of the key considerations was to have gravitational deformations, which vary with telescope orientation, stay within the optical error budget, or ensure that we can compensate with a steering mirror by maintaining predictable elastic behavior. Here we look at several cases where deformation is predicted with finite element analysis and Hertzian deformation analysis and also tested. Techniques used to address thermal deformation compensation without the use of low CTE materials will also be discussed.
We describe the design and first-light early science performance of the Shane Adaptive optics infraRed Camera- Spectrograph (ShARCS) on Lick Observatory’s 3-m Shane telescope. Designed to work with the new ShaneAO adaptive optics system, ShARCS is capable of high-efficiency, diffraction-limited imaging and low-dispersion grism spectroscopy in J, H, and K-bands. ShARCS uses a HAWAII-2RG infrared detector, giving high quantum efficiency (<80%) and Nyquist sampling the diffraction limit in all three wavelength bands. The ShARCS instrument is also equipped for linear polarimetry and is sensitive down to 650 nm to support future visible-light adaptive optics capability. We report on the early science data taken during commissioning.
By inserting a MEMS deformable mirror-based adaptive optics system into the beam transfer optics of the Shane 3-meter telescope at Mt. Hamilton, we actively controlled the wavefront of the outgoing sodium laser guidestar beam. It was possible to show that a purposefully aberrated beam resulted in poorer performance of the Adaptive Optics system located behind the primary, though bad seeing conditions prevented us from improving the system’s performance over its nominal state. A silver-coated Iris AO deformable mirror was subjected to approximately 9.5 hours of exposure to a sodium laser guidestar of 3.5 Watts average output power and showed no signs of permanent damage or degradation in performance. Future applications of the uplink-AO system for correcting atmospheric turbulence and in generating custom laser guidestar asterisms are also discussed.
We present on-sky results obtained with the visible light prototype of the Fibered Imager foR Single Telescope
(FIRST) mounted on the 3-m Shane Telescope at Lick Observatory and using its Adaptive Optics system. This
instrument is dedicated to high angular resolution and high dynamic range imaging. Its principle combines both
techniques of single-mode fiber interferometry and pupil remapping. Simulations predict a dynamic range up
to 106 at /D, or at a few tens of milliarcseconds at 630nm using an 8-m telescope. Laboratory experiments
based on a 9-fiber prototype working in the 600nm–900nm spectral band successfully demonstrated the power
of the concept. The same prototype has been set-up on the 3-m Shane telescope in July 2010. In this paper, we
present the on-sky results obtained in October 2011 with an improved version of the instrument using 18 fibers.
They clearly show the detection of the binary star Capella at the diffraction limit of the telescope.λ
The Lick Observatory 3-meter telescope has a history of serving as a testbed for innovative adaptive optics techniques.
In 1996, it became one of the first astronomical observatories to employ laser guide star (LGS) adaptive optics as a
facility instrument available to the astronomy community. Work on a second-generation LGS adaptive optics system,
ShaneAO, is well underway, with plans to deploy on telescope in 2013. In this paper we discuss key design features and
implementation plans for the ShaneAO adaptive optics system. Once again, the Shane 3-m will host a number of new
techniques and technologies vital to the development of future adaptive optics systems on larger telescopes. Included is a
woofer-tweeter based wavefront correction system incorporating a voice-coil actuated, low spatial and temporal
bandwidth, high stroke deformable mirror in conjunction with a high order, high bandwidth MEMs deformable mirror.
The existing dye laser, in operation since 1996, will be replaced with a fiber laser recently developed at Lawrence
Livermore National Laboratories. The system will also incorporate a high-sensitivity, high bandwidth wavefront sensor
camera. Enhanced IR performance will be achieved by replacing the existing PICNIC infrared array with an Hawaii
2RG. The updated ShaneAO system will provide opportunities to test predictive control algorithms for adaptive optics.
Capabilities for astronomical spectroscopy, polarimetry, and visible-light adaptive optical astronomy will be supported.
The University of California (UC) began operating the Lick Observatory onMount Hamilton, California in 1888. Nearly a
century later, UC became a founding partner in the establishment of theW. M. Keck Observatory (WMKO) in Hawaii, and
it is now a founding partner in the Thirty Meter Telescope (TMT) project. Currently, most UC-affiliated observers conduct
the majority of their ground-based observations using either the Keck 10-meter Telescopes on Mauna Kea or one or more
of the six Lick telescopes now in operation on Mount Hamilton; some use both the Keck and Lick Telescopes. Within the
next decade, these observers should also have the option of observing with the TMT if construction proceeds on schedule.
During the current decade, a growing fraction of the observations on both the Keck and Lick Telescopes have been
conducted from remote observing facilities located at the observer's home institution; we anticipate that TMT observers
will expect the same. Such facilities are now operational at 8 of the 10 campuses of UC and at the UC-operated Lawrence
Berkeley National Laboratory (LBNL); similar facilities are also operational at several other Keck-affiliated institutions.
All of the UC-operated remote observing facilities are currently dual-use, supporting remote observations with either the
Keck or Lick Telescopes.
We report on our first three years of operating such dual-use facilities and describe the similarities and differences
between the Keck and Lick remote observing procedures. We also examine scheduling issues and explore the possibility
of extending these facilities to support TMT observations.
Visible Light Laser Guidestar Experiments (ViLLaGEs) is a new Micro-Electro Mechanical Systems (MEMS)
based visible-wavelength adaptive optics (AO) testbed on the Nickel 1-meter telescope at Lick Observatory. Closed
loop Natural Guide Star (NGS) experiments were successfully carried out during engineering during the fall of
2007. This is a major evolutionary step, signaling the movement of AO technologies into visible light with a MEMS
mirror. With on-sky Strehls in I-band of greater than 20% during second light tests, the science possibilities have
become evident.
Described here is the advanced engineering used in the design and construction of the ViLLaGEs system, comparing
it to the LickAO infrared system, and a discussion of Nickel dome infrastructural improvements necessary for this
system. A significant portion of the engineering discussion revolves around the sizable effort that went towards
eliminating flexure. Then, we detail upgrades to ViLLaGEs to make it a facility class instrument. These upgrades
will focus on Nyquist sampling the diffraction limited point spread function during open loop operations,
motorization and automation for technician level alignments, adding dithering capabilities and changes for near
infrared science.
We describe a project to enable remote observing on the Nickel 1-meter Telescope at Lick Observatory. The purpose
was to increase the subscription rate and create more economical means for graduate- and undergraduate students to
observe with this telescope. The Nickel Telescope resides in a 125 year old dome on Mount Hamilton. Remote
observers may work from any of the University of California (UC) remote observing facilities that have been created to
support remote work at both Keck Observatory and Lick Observatory.
The project included hardware and software upgrades to enable computer control of all equipment that must be operated
by the astronomer; a remote observing architecture that is closely modeled on UCO/Lick's work to implement remote
observing between UC campuses and Keck Observatory; new policies to ensure safety of Observatory staff and
equipment, while ensuring that the telescope subsystems would be suitably configured for remote use; and new software
to enforce the safety-related policies.
The results increased the subscription rate from a few nights per month to nearly full subscription, and has spurred the
installation of remote observing sites at more UC campuses. Thanks to the increased automation and computer control,
local observing has also benefitted and is more efficient. Remote observing is now being implemented for the Shane 3-
meter telescope.
The Lick Observatory is pursuing new technologies for adaptive optics that will enable feasible low cost laser guidestar
systems for visible wavelength astronomy. The Villages system, commissioned at the 40 inch Nickel Telescope this past
Fall, serves as an on-sky testbed for new deformable mirror technology (high-actuator count MEMS devices), open-loop
wavefront sensing and control, pyramid wavefront sensing, and laser uplink correction. We describe the goals of our
experiments and present the early on-sky results of AO closed-loop and open-loop operation. We will also report on our
plans for on-sky tests of the direct-phase measuring pyramid-lenslet wavefront sensor and plans for installing a laser
guidestar system.
The MEMS-AO/Villages project consists of a series of on-sky experiments that will demonstrate key new
technologies for the next generation of adaptive optics systems for large telescopes. One of our first goals is to
demonstrate the use of a micro-electro-mechanical systems (MEMS) deformable mirror as the wavefront correcting
element. The system is mounted the 1-meter Nickel Telescope at the UCO/Lick Observatory on Mount Hamilton. It
uses a 140 element (10 subapertures across) MEMS deformable mirror and is designed to produce diffraction-limited
images at wavelengths from 0.5 to 1.0 microns. The system had first light on the telescope in October 2007.
Here we report on the results of initial on-sky tests.
The wavefront sensor camera and tip/tilt sensor APDs that were on Lick Observatory's Shane 3 Meter Adaptive Optics system were over a decade old and showing their age. They were recently upgraded. The first upgrade was to convert from quad-APDs in the laser guidestar mode natural star tip-tilt sensor to a sensitive low-noise CCD. The new CCD in this position, an 80x80 E2V CCD-39 inside a SciMeasure camera, has a low enough read noise, ~3 e-/pixel, that the tip/tilt measurement in closed-loop operation is photon noise limited and thus benefits from the improved quantum efficiency of the CCD. We have demonstrated on-sky up to two magnitudes of improvement in viable tip/tilt star brightness, which greatly extends the available sky coverage in the laser guidestar AO mode. Also, the increased field of view of the new tip/tilt sensor provides a much more reliable means of acquiring and locking on dim tip/tilt stars, making the whole system operationally more efficient. In the second phase of the upgrade project, the high order wavefront sensor has been replaced, also with a CCD-39 chip in a SciMeasure camera. In this paper we will describe these upgrades and present preliminary performance results.
We report on observations of two quasar host galaxies made with the Lick Observatory adaptive optic system using a laser guide star tuned to the wavelength of the sodium D lines. A brief outline of the system is given, and a description of its performance when obtaining science data. We discuss techniques for obtaining calibration of the point spread function and the analysis steps required to obtain useful scientific results. We present H-band images of quasar host galaxies made with the system. Estimates of the host galaxy
magnitudes and central black hole masses were made from these data.
These are the first observations of quasar host galaxies with a sodium laser guide star.
Current and future large telescopes depend critically on laser guide
star adaptive optics (LGS AO) to achieve their scientific goals.
However, there are still relatively few scientific results reported
from existing LGS AO systems. We present some of the first science
results from the Lick Observatory sodium beacon LGS AO system. We
achieve high sensitivity to light scattered in the circumstellar
enviroment of Herbig Ae/Be stars on scales of 100-200 AU by coupling
the LGS AO system to a near-infrared (J,H,Ks bands) dual channel imaging polarimeter. We describe the design, implementation, and performance of this instrument. The dominant noise source near bright stars in AO images is a "seeing halo" of uncorrected speckles, and since these speckles are unpolarized, dual-channel polarimetry achieves a significant contrast gain. Our observations reveal a wide range of morphologies, including bipolar nebulosities with and without outflow-evacuated cavities and disk-mediated interaction among members of a binary. These data suggest that the evolutionary picture developed for the lower-mass T Tauri stars is also relevant to the Herbig Ae/Be stars, and demonstrate the ability of LGS AO systems to enhance the scientific capabilities of even modest sized telescopes.
Measurements of anisoplanatism from data obtained with natural guide star adaptive optics on the Lick Observatory 3m are presented. These were obtained from short exposures of binary stars with the IRCAL camera whose field of view (~20”) is generally considered isoplanatic in the K-band. However, measurable amounts of high-order anisoplanatism were present at separations of ~7” and ~12” with an isoplanatic patch size estimated to be ~26”. Within this field, there was measureable differential image motion between the binary star components. This image motion was small compared to the size of the diffraction-spot and therefore had negligible effect.
The Lick Observatory laser guide star adaptive optics system has undergone continual improvement and testing as it is being integrated as a facility science instrument on the Shane 3 meter telescope. Both Natural Guide Star (NGS) and Laser Guide Star (LGS) modes are now used in science observing programs. We report on system performance results as derived from data taken on both science and engineering nights and also describe the newly developed on-line techniques for seeing and system performance characterization. We also describe the future enhancements to the Lick system that will enable additional science goals such as long-exposure spectroscopy.
The Lick Observatory laser guide star adaptive optics system has been significantly upgraded over the past two years in order to establish it as a facility science instrument on the Shane 3 meter telescope. Natural Guide Star (NGS) mode has been in use in regular science observing programs for over a year. The Laser Guide Star (LGS) mode has been tested in engineering runs and is now starting to do science observing. In good seeing conditions, the system produces K-band Strehl ratios >0.7 (NGS) and >0.6 (LGS). In LGS mode tip/tilt guiding is achieved with a V~16 natural star anywhere inside a 1 arcminute radius field, which provides about 50% sky coverage. This enables diffraction-limited imaging of regions where few bright guidestars suitable for NGS mode are available. NGS mode requires at least a V~13 guidestar and has a sky coverage of <1%. LGS science programs will include high resolution studies of galaxies, active galactic nuclei, QSO host galaxies and dim pre-main sequence stars.
Adaptive optics performance using a sodium laser guide star at the Lick Observatory 3.0 m telescope is presented. In order to accomplish this the residual effects of natural guide star tip-tilt motion is removed. This is measured from 500 short exposure images (texp = 57ms). The data show instantaneous Strehl ratios ranging from ~ 0.10 to ~ 0.45 with a mean value of ~ 0.26. Centroid tracking of these data yield residual tip-tilt errors of ~ 21 mas, within specifications for the system. This resdual tip-tilt motion reduces the Strehl ratio of long exposure imaging by only ~ 7%.
In 1999, we presented our plan to upgrade the adaptive optics (AO) system on the Lick Observatory Shane telescope (3m) from a prototype instrument pressed into field service to a facility instrument. This paper updates the progress of that plan and details several important improvements in the alignment and calibration of the AO bench. The paper also includes a discussion of the problems seen in the original design of the tip/tilt (t/t) sensor used in laser guide star mode, and how these problems were corrected with excellent results.
Results of experiments with the laser guide star adaptive optics system on the 3-meter Shane telescope at Lick Observatory have demonstrated a factor of 4 performance improvement over previous results. Stellar images recorded at a wavelength of 2 micrometers were corrected to over 40 percent of the theoretical diffraction-limited peak intensity. For the previous two years, this sodium-layer laser guide star system has corrected stellar images at this wavelength to approximately 10 percent of the theoretical peak intensity limit. After a campaign to improve the beam quality of the laser system, and to improve calibration accuracy and stability of the adaptive optics system using new techniques for phase retrieval and phase-shifting diffraction interferometry, the system performance has been substantially increased. The next step will be to use the Lick system for astronomical science observations, and to demonstrate this level of performance with the new system being installed on the 10-meter Keck II telescope.
We present the preliminary results of a laboratory experiment using phase diversity as a wavefront sensor. Computer simulations of this experiment were also performed. The phase diversity algorithm used the ordinary finite-difference method to solve the transport equation of intensity and phase. This method of phase diversity retrieves the phase directly and may prove to be useful for low light level applications and for extended objects. This entertains the possibility of using phase diversity as an on-line wavefront sensor for adaptive optics.
We present the results of some laboratory experiments of the use of electro-optical (EO) devices to control the optical path length (OPL) of an interferometric array. One of the most important problems in interferometric beam combination is the control of the path length; this is coupled with the need for partial wavefront compensation in order to increase the sensitivity of the interferometer. Traditional approaches to such problems are often very expensive and sometimes impractical. For this reason we started an effort, both theoretically and experimentally, in order to investigate if less costly and more effective techniques can be applied. In our experiments we used single-cell LCDs in order to eliminate piston terms in a two- aperture interferometer. We used phase diversity techniques for extracting the phase information. Although the experimental results are still partial we believe that there is enough evidence that such devices can be used for the OPL control and partial wavefront compensation. Further testing is needed in order to assess the real capabilities of commercially available LCDs and the need, if any, of customization.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.