We demonstrate a technique for fabricating microstrip patch antennas using femtosecond laser patterning followed by ultraviolet beam and chemical treatment. Initially, we design the physical parameters of both single-slot and double-slot microstrip patch antennas and simulate them using high-frequency structure simulator for optimization. Simulation results exhibit a return loss of −26 dB at the resonant frequency of 22.9 gigahertz (GHz) for single-slot microstrip patch antenna and −18.3 dB at 24.03 GHz for double-slot microstrip patch antenna. The three-dimensional polar plot and far-field radiation pattern of the microstrip patch antennas confirm excellent directivity of the antennas. Furthermore, we investigate the return loss of the fabricated microstrip patch antennas. For single-slot microstrip patch antenna, experimental result shows a return loss of −21.25 dB at 22.7 GHz. In contrast, double-slot microstrip patch antenna shows a return loss of −27 dB at 24.1 GHz. In addition, we compare the performance of the double-slot microstrip patch antenna fabricated using femtosecond laser-assisted technique and photolithographic technique and find better performance in the femtosecond laser-fabricated microstrip antenna. The proposed femtosecond laser-based technique is simple and shows promises in precise fabrication of high-quality microstrip antennas.
We present a calibration protocol to get the alignment factors of a custom-made spectrometer and the nonlinear fitting
function between the measured CCD pixel domain and the wavelength domain to apply the Fourier-domain optical
coherence tomography (FD-OCT) using optical fiber gratings. We have used 5 different center wavelength gratings
covered the broadband source spectral range with a narrow spectral bandwidth (<0.05 nm) and the same reflectivity
(>92 %) to calibrate and align the custom-made spectrometer. The implemented SD-OCT system following the proposed
protocol showed the alignment factors as 44.37o incident angle, 53.11o diffraction angle, and 70.0 mm focal length. The
spectral resolution of 0.187 nm was recalculated from the alignment factors.
Experimental proof-of-concept is presented for a quasi-holographic solution to polarization-sensitive optical coherence tomography (PS OCT). Due to decoupling between the reference and sample beams by polarization, the solution seems acceptable to acquisition and communication of optical data in the nonlaboratory environment. The nonlab environment implies uncontrollable disturbances, e.g., temperature changes and mechanical effects happening under shop testing in industry or routine examinations in common clinics and hospitals. For mapping the collagen-related depolarization ratio of light backscattered from the human dermis, a phenomenological model is evolved from the theory of light depolarization in crystalline polymers. The model yielded a simplified intensity-based estimation algorithm. The design concept and the model rely on a submillimeter tumor thickness as a proofed prognostic factor and an important criterion for complementary functional diagnostics of skin cancers in their early phase. Choice of the model is inspired by similarity of structural and optical properties between liquid-crystal collagen fibers in the dermis and birefringent crystalline lamellae in some polymer materials. The model gives a plausible interpretation of a peculiarity of cumulative birefringence in the abnormal skin dermis. Following a top-down approach to design, the authors attempt to contribute to bridging the gap between practitioners' concerns and academic studies.
We demonstrate a novel implementation of spectral domain OCT by using a proposed sweeping detector at 1320 nm
wavelength range. A fiber pigtailed Fabry-Perot tunable filter is newly adapted to receive spectral interferometer
information using a photo-receiver instead of using charged couple detector arrays. In order to show a possibility of the
scheme in other view point, we have changed the position of the Fabry-Perot tunable filter of the interferometer. The
combination of a super luminescent LED and a semiconductor optical amplifier was used as an optical source. Its output
power is about 10 mW and the spectral bandwidth is about 60 nm. The filtered light after passing thorough the Fabry-
Perot tunable filter has 0.15 nm instantaneous spectral linewidth with 1.3 mW average output power. The system with an
axial resolution of 12 μm performed OCT imaging of a cornea of a rat eye proving potential about the application of the
proposed sweeping detector OCT.
There have been several technologies to enable high resolution cross-sectional images of biological tissues in optical coherence tomography (OCT) method. Optical frequency comb (OFC) source has been proposed to overcome the crosstalk problem among the CCD detector pixels of the continuous spectrum of light source. Recently, a passive-type OFC is demonstrated simply placing a Fabry-Perot interferometer filter right after the broadband light source, but it shows a high loss of output light power and limited tenability of channel spacing of multi-wavelength. In this work, we experimentally demonstrate a spectral comparison of a novel multi-wavelength source based on a fiber Sagnac interferometer. The channel spacing is flexibly tuned by the effective length control of polarization-maintaining fiber (PMF). The uniform and stable multi-wavelength spectral distribution is also helpful to obtain the higher sensitivity from the lower exposure intensity source to get a better quality spectral OCT image.
A further insight into the prior concept of polarization sensitive optical coherence tomography system intended for non-laboratory
conditions is brought forward and an experimental proof-of-concept is presented. A phenomenological model
is adopted from the theory of light depolarization in crystalline polymers and modified to yield a simplified algorithm for
mapping depolarization ratio in dermis. The algorithm could distinguish between dermal layers with depleted collagen
content and normal dermis of normal perilesional skin. Dermis is simulated by bireringent lamellae of collagen arranged
chaotically in multiple layers parallel to the skin surface. Both the design concept and the model imply the sub-millimeter
tumor thickness as a proofed prognostic factor and an important criterion for complementary functional
diagnostics of skin cancers at their early phase of vertical growth. Choice of the model is inspired by similarity of
structural and optical properties between liquid-crystal collagen fibers in dermis and birefringent crystalline lamellae in
polymer materials. The numerical computation based on the model allowing for real characteristics of dermis gives
plausible interpreting of depolarization peculiarities caused by collagen depletion. Feasibility is discussed of exploiting
fiber optic analogs of achromatic retarders. Fabrication of the fiber retarders is shown to be realistic by making use of the
photonics technology possessed by the authors.
We have demonstrated bandwidth control and reshaping of second harmonic (SH) curve in a periodically poled Ti:LiNbO3
(Ti:PPLN) waveguide ( period=16.6 um) by using a temperature-gradient-control technique and a local-temperature-control technique.
We have achieved more than 13 nm second harmonic phase-matching bandwidth and several useful shapes of SH curve such as almost ideal sinc function, and double peaks in a 74 mm long Ti:PPLN waveguide that has pre-chirped SH curve in room temperature.
By using volume holography characteristics, optical devices having demultiplexer and/or dispersion compensator capabilities are proposed which can control multiple channel wavelengths in the wavelength division multiplexed (WDM) system. Through a specially designed mask system, multiple volume gratings corresponding to the multi-channel components are recorded in a photorefractive crystal. This mask recording scheme simplifies the conventional sequential multiplexing procedure which requires complex mechanical or laser source system. Recording schemes and device characteristics of the above devices are presented in relation with volume diffraction principle and photorefractive crystal properties.
With adoption of wavelength division multiplexing scheme to optical communication systems, multiwavelength optical signal source has drawn considerable attention. The conventional multiwavelength sources usually consist of the same number of lasers as wavelength channels and therefore become bulky and costly. In this paper, we propose and implement a novel multiwavelength generation scheme using a high-birefringence fiber loop mirror in a semiconductor-fiber ring laser. Due to the inhomogeneous gain broadening characteristics of semiconductor optical amplifier, up to 22 channels with 0.8 nm wavelength spacing can be obtained at room temperature.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.