|
1.IntroductionMorphological and spectral measurements are the two major methods of analyzing rock structures and compositions.1 An imaging spectrometer has the ability to simultaneously obtain both the images and the spectral signatures of targets and is widely used in terrestrial and space-based remote sensing applications. Mineralogical composition analysis is one of the major tasks of China’s lunar exploration project.2 Minerals such as pyroxene, plagioclase, olivine, and ilmenite, in different sizes and shapes, constitute most of the lunar surface rocks.3 The minerals have distinctive spectral characteristics in the VIS/NIR and short-wave infrared (SWIR) wavebands that can be used for identification. Figure 1 shows the spectral reflectance curves of the primary rock-forming single minerals that can be used for mineral identification.4 Imaging spectral remote sensing is one of the most important scientific achievements in the past 20 years of the 20th century. Imaging spectrometry combines the imaging technology of traditional remote sensing and spectrum analysis technology. Acousto-optic tunable filter (AOTF), which operates based on acousto-optic interaction, is an electronically tunable optical filter. AOTF has special features compared to other dispersive parts, such as solid state and programmable. An imaging spectrometer based on AOTF is especially suitable for deep space exploration applications (Moon, Mars, and asteroid detection), because of the characteristics such as electronically tunable spectral selectivity, environmental adaptability, rapid response, and simple structure.5–7 As early as 1987, a spaceborne spectrometer based on AOTF was developed in the former Soviet Union for ocean exploration. European Space Agency (ESA) successfully launched the Mars Express loaded with the SPICAM (Spectroscopy for Investigation of Characteristics of the Atmosphere of Mars) spectrometer in 2003.8 In 2005, ESA Venus Express satellite was also loaded with AOTF spectrometer for Venus detection.9 Since 2006, the Shanghai Institute of Technical Physics began to study imaging spectrometers based on AOTF. Visible and near-infrared imaging spectrometer (VNIS) is a payload of lunar rover for 0.45- to spectral bands detection and will be able to inspect and probe minerals in the rover region. Lunar mineralogical spectrometer (LMS) is a payload integrated with a scanning module and spectral programmable imaging spectrometer for a future lunar lander. 2.Spectrometers Based on AOTFs2.1.Visible and Near-Infrared Imaging SpectrometerThe VNIS is one of the main scientific payloads on the lunar rovers for Chang’e 3 and Chang’e 4. It uses AOTFs as the dispersive components.10,11 The VNIS mostly addresses the lunar surface material composition and available resource exploration for determining the lunar surface mineral composition and performing a comprehensive analysis of the chemical compositions. The VNIS is mounted on the platform of the lunar rover and detects the spectra and images of the lunar objects in the roving area to provide scientific data.9 As a passive optical instrument, the VNIS measures the radiance diffusely reflected from solar illumination of the Moon’s surface. It includes two detection channels: a VIS/NIR channel (0.45 to ) with a CMOS area array detector and a SWIR channel (0.9 to ) with an InGaAs single-element detector. Each channel consists of image-forming lens, field stop, collimating lens, convergent lens, and the AOTF. Furthermore, a calibration unit with dust-proofing functionality, motor drive circuit, radio frequency (RF) drive circuits, and main control circuits has been integrated in this payload as the public component, as shown in Fig. 2. The structure, optical module, and design of the VNIS are detailed in Figs. 3 and 4. As shown in Fig. 4, two types of AOTFs have been used in the optical system. Each AOTF has two transducers with separate ports to optimize the bandpass (FWHM) and diffraction efficiency. Furthermore, an optical wedge has been designed at the exit port to eliminate chromatic aberration in both AOTFs. The main characteristics of the VNIS AOTFs are shown in Table 1. The performance of AOTFs such as acoustic frequency range and diffraction efficiency is shown in Fig. 5. Table 1Main characteristics of the VNIS AOTFs.
After its soft landing on the Moon, Chang’e 3 carried out a lunar survey followed by scientific exploration activities. The VNIS mostly analyzed the lunar surface material composition and explored the available resources. The VNIS operated in two modes: detection and calibration. In the detection mode, the VNIS acquired scientific data from the lunar surface objects; the angle between the framework of the calibration unit and the horizontal mounting face of VNIS was about 55 deg. In the calibration mode, using solar radiation as the calibration source, the diffusing calibration plate of the calibration unit was set to a position parallel to the mounting plane to allow calibration of the instrument. The calibration unit of the VNIS at the light entrance consisted of an ultrasonic motor (USM), harmonic reducer, framework, and an internal diffuser panel. The operating modes and dust-proofing function were realized by the self-locking characteristics of the USM.10 The structure and function of the calibration unit are shown in Fig. 6. The VNIS was mounted in front of the lunar rover to detect lunar surface objects at a 45-deg viewing angle and to obtain the spectra and geometric data at a height of 0.695 m, as shown in Fig. 7. 2.2.Lunar Mineralogical SpectrometerThe LMS is one of the main scientific payloads onboard the lunar landers for Chang’e 5 and Chang’e 6. The LMS primarily follows the technology of the VNIS but expands its spectral range from 0.48 to . It has the following functions: (1) to obtain the spectral image data of the specified objects in the VIS–NIR and spectral data in the SWIR channels, (2) to perform in-situ calibration, and (3) spectral imaging and spectral detection with multiband in full scanning region. The LMS includes four detection channels: one is a hyperspectral imager with a spectral range of 0.48 to , and the others are three spectrographs and their total spectral range being 0.9 to . The LMS includes a two-dimensional (2-D) scanning mechanism, image-forming lens, collimating lens, AOTF, convergent lens, the detector components, motor drive, RF drive, and a main control circuit, as shown in Fig. 8. It is a kind of scanning, spectral programmable imaging spectrometer and includes a scanning mechanism and a programmable spectral selection spectrometer. As shown in Fig. 9, two AOTFs have been used in the optical system. They also have ports to optimize the bandpass (FWHM) and diffraction efficiency. The order diffraction light of the VIS–NIR AOTF was used for the VIS spectral imaging and NIR spectra acquirement, where an optical wedge was designed for the AOTF to eliminate chromatic aberration. The order diffraction lights of the IR AOTF were used for the SWIR and MWIR channels, respectively. The main characteristics of these AOTFs are shown in Table 2. Table 2Main characteristics of the VNIS AOTFs.
After spectral calibration, the spectral resolution was 2.4 to 9.4 nm in the VIS–NIR and 7.6 to 24.9 nm in the IR channels, as shown in Fig. 10. Images of the lander and LMS are shown in Fig. 11. The LMS is mounted on the panel of the lander to detect the lunar surface objects and obtain the spectra and geometric data at a height of about 1.55 m. Because the platform on which the LMS is mounted is unmovable, a pointing component is required for expanding the observable areas. The 2-D scanning mechanism includes USMs, harmonic reducer, rotary potentiometers, and an aluminum-based scanning mirror, which ensure that the system is light and minimized and the system can adapt to a high surrounding temperature of up to 94°C. 3.Main Characteristics and Primary Detection Results3.1.Visible and Near-Infrared Imaging SpectrometerThe VNIS can simultaneously obtain a spectral image in the VIS/NIR channel and spectral data in the SWIR channel. The optical axis of the VIS/NIR and SWIR channels are parallel to each other at a distance of 18 mm. The fields of view (FOVs) in the VIS/NIR and SWIR channels are and , respectively. According to the spectral calibration, the spectral ranges of the VNIS are 449 to 950 nm with 2- to 7-nm resolution in the VIS/NIR channel and 899 to 2402 nm with 3- to 12-resolution in the SWIR channel, which are shown in Fig. 12. The signal-to-noise ratio (SNR) of the VNIS is tested and analyzed by ground radiometric calibration. The SNR changes with the input signal, and it is an important indicator of the radiometric response characteristics of the VNIS. The SNR is in the VIS–NIR band when the albedo is 0.09 and the solar incident angle is 45 deg; and the SNR is in the SWIR channel when the albedo is 0.09 and the solar incident angle is 75 deg.10 The main performance specifications of the VNIS are shown in Table 3. Table 3Main performance specifications of VNIS/Yutu.10
After the Chang’e 3 mission began its scientific exploration stage, the VNIS instrument successfully completed the first lunar surface spectral acquisition at BTC 10:10 on December 23, 2013. During the first two lunar days, the VNIS performed measurements at four locations and obtained data in detection mode (four times) and calibration mode (three times). The total size of data was 350 MB.11 The topographical images of N205 and the REFF of all detection nodes are shown in Fig. 13. During the Chang’e-4 mission, VNIS was carried on Yutu-2 lunar rover. Since the successful soft landing in Von Kármán crater on the far side of the Moon on January 3 2019,12 VNIS had been working for five lunar days and performed 27 detections. The selected targets such as Yutu-2’s wheel track and rock, obtained in the detection node A and LE00303, and their corresponding REFF features are shown in the Fig. 14. 3.2.Lunar Mineralogical SpectrometerIn the detection mode, the LMS obtained spectral images in the VIS/NIR channel and spectral data in three SWIR channels in sequence. The main performance specifications of the LMS are shown in Table 4. Table 4Main performance specifications of the LMS.
Performance parameters such as FOV, spectral range, spectral resolution, radiance, and geometric imaging features were calibrated in the ground experiment. The FOV of the LMS was in all channels. The SNR is in the VIS/NIR band, and in the IR band, as shown in Fig. 15. 4.ConclusionsTo analyze the composition of the lunar surface minerals, several spectrometers based on AOTFs have been developed to detect lunar surface objects and to obtain their reflectance spectra and geometric images; these include the VNIS onboard China’s Chang’e 3 and Chang’e 4 lunar rovers and the LMS onboard Chang’e 5 and Chang’e 6 lunar landers. These spectrometers are capable of synchronously acquiring the full spectra of the lunar surface objects and performing in-situ calibrations. The VNIS/Yutu has performed several explorations and calibrations, and obtained several spectral images and spectral reflectance curves of the lunar soil in the Imbrium region following its first successful operation at the landing site on December 23, 2013. The VNIS/Yutu-2, which is travelling in Von Kármán crater after the soft landing on January 3, 2019,12 will provide valuable in-situ hyperspectral images and infrared spectra of the soil, rocks, and other materials on the far side of the Moon. The flight module of LMS has completed all the ground calibration and environmental verification tests and will observe the sampling area in the lunar surface sampling mission with the Chang’e 5 probe by the end of 2019. AcknowledgmentsThis paper was supported by the special funds for the second and third phases of the Chinese lunar exploration program, the National Natural Science Foundation (Nos. 21105109 and 61605231), and the Program of Shanghai Academic/Technology Research Leader (No. 19XD1424100). The authors thank the Science and Application Center for the Moon and Deep Space Exploration of the Chinese Academy of Sciences for the ground test and data preprocessing and the National Space Science Center of the Chinese Academy of Sciences for its contributions to the development and testing of the instruments. ReferencesZ.-P. He et al.,
“Operating principles and detection characteristics of visible and near-infrared imaging spectrometer (VNIS) in Chang’e 3,”
Res. Astron. Astrophys., 14
(12), 1567
–1577
(2014). https://doi.org/10.1088/1674-4527/14/12/006 1674-4527 Google Scholar
P. J. Ye and J. Peng,
“Deep space exploration and its prospects in China,”
Eng. Sci., 8
(10), 13
–18
(2006). ENSCAT 0013-7812 Google Scholar
B. Liu et al.,
“Reflectance conversion methods for the VIS/NIR imaging spectrometer aboard the Chang’E-3 lunar rover: based on ground validation experiment data,”
Res. Astron. Astrophys., 13
(7), 862
–874
(2013). https://doi.org/10.1088/1674-4527/13/7/010 1674-4527 Google Scholar
Z. He et al.,
“Visible and near-infrared imaging spectrometer (VNIS) and its preliminary results from the Chang’E 3 Project,”
Rev. Sci. Instrum., 85 083104
(2014). https://doi.org/10.1063/1.4891865 RSINAK 0034-6748 Google Scholar
O. Korablev et al.,
“Development of a mast or robotic arm-mounted infrared AOTF spectrometer for surface Moon and Mars probes,”
Proc. SPIE, 9608 960807
(2015). https://doi.org/10.1117/12.2190450 CRETAG 1016-2437 Google Scholar
J.-P. Bibring et al.,
“The MicrOmega investigation onboard Hayabusa2,”
Space Sci. Rev., 208 401
–412
(2017). https://doi.org/10.1007/s11214-017-0335-y SPSRA4 0038-6308 Google Scholar
Zh. He et al.,
“Visible and near-infrared imaging spectrometer (VNIS) for Chang’E-3,”
Proc. SPIE, 9263 92630D
(2014). https://doi.org/10.1117/12.2069193 PSISDG 0277-786X Google Scholar
J. Wang et al.,
“Visible and near-infrared imaging spectrometer aboard Chinese Chang’E-3 spacecraft,”
Optical Payloads for Space Missions, John Wiley & Sons, Chichester
(2015). Google Scholar
J.-L. Bertaux et al.,
“SPICAV on Venus Express: three spectrometers to study the global structure and composition of the Venus atmosphere,”
Planet. Space Sci., 55
(12), 1673
–1700
(2007). https://doi.org/10.1016/j.pss.2007.01.016 PLSSAE 0032-0633 Google Scholar
Zh. He et al.,
“Visible and near-infrared imaging spectrometer (VNIS) for in-situ lunar surface measurement,”
Proc. SPIE, 9639 96391S
(2015). https://doi.org/10.1117/12.2194526 PSISDG 0277-786X Google Scholar
Zh. He et al.,
“The spectrometers based on AOTF for in-situ Lunar surface measurement,”
Proc. SPIE, 10780 107800N
(2018). https://doi.org/10.1117/12.2324437 PSISDG 0277-786X Google Scholar
C. Li et al.,
“Chang’E-4 initial spectroscopic identification of lunar far-side mantle-derived materials,”
Nature, 569 378
–382
(2019). https://doi.org/10.1038/s41586-019-1189-0 Google Scholar
BiographyZhiping He is a professor in Shanghai Institute of Technical Physics of the Chinese Academy of Sciences. He has long been engaged in the research of space optics and optoelectronic technology and has participated and completed the development of Chang’e 3 visible and near-infrared imaging spectrometer (VNIS). Currently, he is conducting several researches on the spectral detection payloads, which are used for the exploration of Moon and Mars. The representative work includes Chang’e 5 lunar mineralogy spectrometer (LMS) and Mars mineralogy spectrometer (MMS). |